Canon Printer B200 Error message Troubleshooting Guide

One of the most dreaded errors for Canon Printer users is the Canon Printer B200 Error. This type of error is quite prevalent in a lot of Canon printers. Also, it typically indicates that there is something wrong with the Printer and its key parts.

If you are also encountering this same issue that you don’t need to instantly junk your Canon printer or replace its possibly faulty components. In this article, we have described the best troubleshooting steps in order to quickly resolve the issue without wasting the time.

Causes of Canon Printer B200 Error message:

Look for the reasons of causing this error:

1: Most of the users have reported that they are suffering from Canon B200 Error. A Canon B200 error usually points defective print head and it is also an important printer component.

2: Moreover, it is also responsible for disturbing ink from the cartridges into the paper printout. Print heads are particularly prone to problems and especially affordable Canon Pixma models.

3: The other cause of this error usually occurs when the different formulas of ink have been utilized by the printer. However, this error sometimes occurs when you replace or refill an OEM cartridge with not a legitimate product.

How to Fix Canon Printer B200 Error?

Usually, you can fix this error quickly by just turning off your printer and allowing it to cool down immediately. The Canon Printer Error B200 can cause due to external debris clogging on the rollers and un-removed paper jams. Also, there comes sometimes when you need to temporarily shut down your computer and thus it can help in resolving your problem.

The solution might work immediately and thus allow you to get back on where you left off. However, if there is another method then you can also try that. Also, the process will depend on the number of ink cartridges that your Canon Printer uses.

Here we have defined some steps to fix the Canon printer B200 error:

Solution 1 – Check Paper Jam:

To check the Paper Jam issues use these following methods:

1: Firstly, turn off your Printer.

Turn your printer on to fix Canon Printer B200 Error message

2: Now, unplug the printer for up to 10 minutes.

unplug

3: Next, you need to take the paper out of the printer.

paper jam

4: Here you need to carefully check if there is any paper jam or obstruction in the path of the paper.

5: However, if nothing is found then you need to re-plug and restart the Printer.

unplug

Solution 2 – Clean Print Head:

In order to clean Print Head you need to follow these given steps:

1: First, unplug your printer and then take out the cartridges.

open cartridge

2: Now, take out the print head and then clean it using some alcohol and shake it occasionally.

locate the glass printhead

3: Next, using alcohol you can easily clean the connectors that connect the print heads to the printer.

4: Once you dry the print head for a specific amount of time then again you need to reconnect it to the printer along with the cartridges.

open cartridge

5: Now, slide the print head to the left.

6: Re-plug your Canon Printer.

7: Put the printer cover down and then turn on the printer.

turn off your printer

Solution 3 – Reset Print Head:

To reset Print Head, you need to follow these steps:

1: Firstly, you need to unplug your Canon Printer.

unplug to fix Canon Printer B200 Error message

2: Now, open the cover so that you can view the print head.

3: Slide print head to the center.

locate the glass printhead

4: Now, re-plug your print head and turn it on, and also the cover remains open.

5: Next, the print head will start to move.

printer color cartridge to fix Canon Printer B200 Error message

6: As, the print head starts, close its cover.

7: Now, let the printer reboot.

turn off your printer

Solution 4 – Remove Old Ink:

When the ink start becomes old, then it can start becoming hard inside the print head and this causes obstructions too. Also, it may be the reason for seeing the Canon B200 error on your Canon Printer.

Therefore, we will suggest taking out the old ink and cleaning the print head with hot water, and then drying the print head and place it back again. Now, you can ensure that this error has been resolved and if not then follow the next method.

Solution 5 – Remove Obstructions:

In order to fix this error, you can make use of a flashlight and carefully inspect the left and center locations for an obstruction. You can also make use of tweezers and long-nose pliers to carefully remove it. Next, you need to gently slide the carriage to the left side of the printer until it stops.

Solution 6 – Reset Printer:

Here has been listed some steps to reset your Canon Printer:

1: Press Setup.

Press Setup

2: Now, press the arrow buttons until you navigate to Device settings and then press Ok.

Device settings to fix Canon Printer B200 Error message

3: Press the arrow button until you navigate to the Reset setting and then press Ok.

navigates the Reset Setting

4: Again, press the arrow button, until you navigate to Reset all and then press Ok.

5: Select Yes.

6: Press Ok and your device is now reset.

Solution 7 – Restart Your System:

Follow these steps to restart your computer:

1: Firstly, you need to press and hold the power button on the front of the computer for approx 5 seconds.

power on pc

2: Now, the computer will get shut off and no light should be near the power button. However, if the lights are still on then you can unplug the power cord to the computer tower.

3: Wait for 30 seconds.

4: Now, push the power button to turn the computer on again.

power on pc to fix Canon Printer B200 Error message

Solution 8 – Replace the Tank:

You can resolve the Canon B200 error by simply replacing the tank holder. Else, you can also purchase a new one and replace your current tank holder.

You can also follow these steps to replace the tank:

1: Firstly, you need to ensure that the printer is turned on and then you need to open the Print headcover.

2: Now, you need to remove the empty ink tank by do the following steps:

  • Push the tab.
  • Remove the ink Tank.

Remove the ink Tank

3: Now, lift it from its slot and remove the ink tank and start preparing a replacement tank.

Solution 9 – Check Ink Cartridge:

As you keep using your Canon printer, its cartridge starts to become faulty. Thus, it is possible that you may see the Canon B200 error. So, the most ideal solution is you need to purchase a new ink cartridge for your Canon Printer. And, also you need to make sure that you check the new ink cartridge properly and then check your B200 Canon Printer error and if it is still there then you can follow the next step.

Solution 10 – Use Power and Copy Buttons:

You might feel glad to know that pressing the copy and power buttons together with your Canon Printer can also fix this error. So, let’s try it out you can read the given steps to quickly remove the Canon B200 error.

Follow these steps carefully:

1: You need to simultaneously press the Power and Copy buttons of your Canon Printer.

2: You can repeat this step multiple times.

3: Now, the printer will get started.

4: Here you need to run the nozzle check procedure.

Nozzle-check to fix Canon Printer B200 Error message

5: Next, you need to run the deep cleaning procedure.

6: Now, you need to perform the printer alignment procedure.

print allignment to fix Canon Printer B200 Error message

7: Next, you can use your Canon Printer to ensure that the Canon Printer B200 error has been settled now.

Solution 10 – Inspect Canon Pixma Printer:

In case if you see the Canon PIXMA B200 error message then this solution is quite helpful. In this solution, you will learn how you can check your Canon PIXMA Printer for causing this error. You can read these given steps below:

1: Firstly, access the Top cover of your Canon printer and then remove it.

2: Now, remove the cover of the cartridge.

3: Next, remove the print head of the device.

locate the glass printhead

4: Insert the print head of the printer again.

5: Latch the lever.

6: Now, position the cartridges again.

open cartridge

7: Next, you need to check whether the Canon PIXMA B200 error has been fixed and if not then keep reading the next steps.

8: Remove the power plug of your printer.

unplug

9: Now, plug in the power plug after 5 minutes.

10: Next, you need to run the cleaning process and then run the nozzle check procedure.

11: Uninstall and then re-install the ink cartridges.

open cartridge to fix Canon Printer B200 Error message

Solution 11: Install Canon printer driver again:

Have you correctly install the Canon Printer driver on your system? If not, then you can easily guess the source for causing this B200 ERROR. Thus, reinstalling the driver is quite helpful and this solution should be tried.

So, let’s read the steps very carefully:

1: First, you need to click on Start and then open the Control Panel.

control panel to fix Canon Printer B200 Error message

2: Now, click on “Hardware and Sound”.

Hardware and sound option windows 7

3: Tap on Devices and Printers .

click on devices and printers to fix Canon Printer B200 Error message

4: Now, choose the model that needs to be deleted.

5: Next, you need to tap the Alt Key and then select Delete from the file menu.

remove printer from control panel

6: Click on continue when you see the Account control dialog box has been shown.

7: Now, click “Yes”.

8: Here you need to choose the printer driver that has to be deleted.

Remove Driver and Driver package to fix Canon Printer B200 Error message

9: Now, you need to again tap the Alt key on the keyboard and then choose “Run as Administrator” from the file menu.

10: Tap on Server Properties.

Printer server Properties to fix Canon Printer B200 Error message

11: Now, you need to click on Continue when the Account Control dialog box shows up.

12: Next, you need to go to the Drivers Tab.

13: Now, choose the printer from the list of printer drivers installed.

14: Delete the driver tab by clicking on Remove.

Click the Remove buttonunplug to fix Canon Printer B200 Error message

15: You also need to choose the Remove Driver and Driver package and then press “Yes”.

16: Once the data collection gets completed then you need to click on Delete in the Remove Driver Package dialog box.

17: Now, press Ok to finish the procedure.

Remove Driver and Driver package

18: Next, you need to open the Canon Support page.

19: Type the model number of your printer.

Search printer name in search fieldunplug to fix Canon Printer B200 Error message

20: Here you need to choose Driver and Downloads.

click on select driver

21: Now, click on Select and then press Download.

click on downloadunplug to fix Canon Printer B200 Error message

22: Finally, you need to install downloaded files and the process will be over.

Solution 12: Reset Canon Printer:

The next fix that we have for the Canon Support B200 error evolves restarting your printer. However, this fix can be easily performed with minimum effort.

So, look at these given steps:

1: Firstly, you need to unplug your Canon Printer.

unplug to fix Canon Printer B200 Error message

2: Now, leave your Canon Printer idle for at least 30 minutes.

3: Let your printer cool down for some time.

4: Next, plug in the machine.

5: Now, when your printer gets started then give a test print.

Frequently Asked Questions (FAQ’s)

Q1: What are the steps for fixing CANON B200 ERROR?

Ans: Here has been defined some steps for fixing Canon B200 Error:

1: First, you need to reset the Printer.

2: Now, remove the obstructions.

3: Clean the Print head.

4: You need to manually clean the print head.

5: Remove old ink cartridges.

6: Re-install the Printer Drivers.

7: Give a try to the new ink cartridge and several others.

Q2: How you can clear the error code on Canon Printer?

Ans: Follow these steps in order to clear error code on Canon Printer:

1: First, switch on the Printer.

2: Now, press and hold the stop/reset button.

3: Here you need to press the button in order to make a color copy and then hold it down.

4: Next, you need to wait for 5 seconds.

5: Here the printer reboots and sets itself up.

6: Finally you have reset your Printer.

Q3: How you can get Canon Printer out of state?

Ans: Here has been listed some steps to get Canon Printer out of error state are:

1: Press the Windows Logo key +R on your keyboard and then type devmgmt.msc and then hit enter to open the Device Manager.

2: You need to make sure that the printer is online.

3: Now, re-install the printer driver.

4: Set the Printer spooler service to automatic.

5: Update the Windows.

Q4: How you can fix Printer errors?

Ans: In order to fix Printer errors, follow these given steps:

1: First, you need to open the Printer Troubleshooter and then Enter Troubleshoot in the text box to search for troubleshoots settings.

2: Now, click the print Spool folder.

3: Next, you need to check the Printer ports settings.

Q5: How you can reset Canon Printer?

Ans: To reset Canon Printers follow these given steps:

1: First, press setup on your Canon device and then navigate to Device settings through arrow keys and then press Ok.

2: Now, you need to navigate to Reset setting and then press Ok and then navigate to “Reset all option”.

3: Next, press Ok and then select Yes and your device have now been reset.

Final words

By following all the above methods you can get rid of the issue of Canon B200 ERROR. Try these steps one by one and see which methods work best for you. However, if it won’t resolve the issue then you can directly communicate with our team of experts and get reliable solutions for resolving this error.

You can directly communicate with us via chat and get assured that your problem gets resolved within a couple of times. So, feel free to contact us and ask your queries in our given comment section below. We surely deliver hassle-free solutions to all your printer-related problems.

Leave a Reply

Your email address will not be published. Required fields are marked *